|Industrial dust treatment equipment series|
|Welding fume exhaust gas treatment series|
|Grinding polishing dust removal equipment|
|Stand-alone dust collector|
|Spiral duct and accessories series|
Main points of dust removal equipment operation , what should be checked before starting?
The dust removal equipment must be used well. The correct design and good manufacturing and installation of the dust removal equipment manufacturers are important, but the daily use management should also be taken very seriously. If the dust removal equipment is out of order, if it is not found in time and resolved in time, the effect of the dust removal equipment will suddenly drop and the dust removal effect will not be achieved. Now let's talk about several important issues in the operation of dust collector equipment.
： 除尘设备初次运行时要检查除尘设备在装置时候中和安装完成后有没有认真的检查，以保证工业吸尘设备的质量安全。 1 : When the dust removal equipment is first run, check whether the dust removal equipment is carefully checked during the installation and after the installation is completed to ensure the quality and safety of the industrial dust collection equipment.
：除尘设备厂家在 安装时要查看布袋除尘设备箱体有连接的地方，是否连接紧固，要密封处理的地方，密封的效果是否合理，焊接的地方有没有漏气，花板在焊接的时候有没有变形。 2 : During the installation of the dust removal equipment manufacturer , check the bag dust removal equipment box where there is a connection, whether the connection is tight, the place to be sealed, the sealing effect is reasonable, there is no air leakage in the welding place, the flower plate is in the Is there any deformation? The inspection of the cabinet is an important place to check the operation of the dust collector equipment.
：箱体 检查之后再安装工业吸尘设备的滤袋。 3 : Install the filter bag of industrial vacuum equipment after the box inspection. When installing, it depends on the fit of the cloth bag and the cage. The cloth bag is installed on the flower plate of the dust collector. You can go inside the ash hopper to see if the filter bag has a collision phenomenon, and you can adjust it by hand.
：在 检查除尘器设备的机械部位，检查进气、出气和风阀开光能不能全部开启和全部关闭，能不能完全锁住，检查除尘设备的限位开关的指示。 4 : In checking the mechanical parts of the dust collector equipment, check whether the intake, outlet, and damper opening lights can be all turned on and off, and whether they can be completely locked. See if the operation of the ash conveying device is normal and whether the blade of the screw conveyor touches the bottom. This is the main point of checking the ash discharge operation of the dust removal equipment.
单机除尘器 设备 清灰装置在装配前要查看喷吹气管上的喷吹孔的直径大小和孔的距离，如果没有问题后在安装。 5: The dust removal device of the stand-alone dust collector equipment should be inspected before the assembly of the diameter and distance of the injection hole on the injection air pipe. If there is no problem, install it. Dust removal equipment manufacturers also need to check whether the pulse valve, the pulse valve, and the blowing pipe are sometimes leaking when they are connected. The hole of the air jet is not aligned with the middle of the bag, and whether there is any problem with the sound when the pulse is heard.
：对进入的 空气需要检查过滤器、干燥器是不是正确的，空压机是不是到了设定的压力就停止动作。 6 : It is necessary to check whether the filter and dryer are correct for the incoming air, and whether the air compressor stops to reach the set pressure. If not, check whether the pressure control device is normal. There should be a safety valve on the air compressor to check whether it is working normally. The inspection of the gas is also one of the inspections of the operation points of the dust removal equipment.
：检查打磨抛光除尘设备的操作 系统要认 证 PLC 的运行情况 ，另外，还要确定除尘设备的风机的运转的情况，没有有反转。 7 : Check the operating system of the polishing and dust removal equipment to verify the operation of the PLC . In addition, make sure that the operation of the fan of the dust removal equipment is not reversed.
启动前一个重要的安全保障，防止了启动前一些可能会存在的问题，保障了以后除尘器设备、工业吸尘设备更好的使用，更长久的使用！ Checking the operation points of the dust removal equipment is an important safety guarantee before the startup of the dust removal equipment , preventing some problems that may exist before startup, and ensuring better use of the dust collector equipment and industrial vacuum equipment in the future and longer use!