⎝⎛足球正网开户⎞⎠

Dongguan Yuchen Machinery Technology Co., Ltd. Industrial dust removal equipment manufacturers provide industrial dust extraction equipment, dust collector equipment, industrial dust collector equipment, grinding dust removal equipment, polishing dust removal equipment, workshop dust removal equipment, and provide a complete set of design solutions for workshop dust treatment plant dust treatment, Quotation, see on-site service
Dongguan Yuchen Industrial Dedusting Equipment Manufacturer
Provide dust removal plan for grinding and polishing dust removal equipment workshop
Unified national service hotline:
0769-81256298 400-622-6298 0769-81256298

Precautions when starting and operating the pulse bag filter


那么有很多用户会想要注意什么事项才能使脉冲布袋除尘器除尘效果好并使用时间更长.现在由小编与大家一起详细了解脉冲布袋除尘器的开机与运转时的注意事项 . The pulse bag dust collector is widely used in industry , so there are many things that users will want to pay attention to to make the pulse bag dust collector have a good dust removal effect and use it for a longer time . Now Xiaobian and everyone will learn more about the startup of the pulse bag dust collector. And precautions during operation .

I. Check before starting the pulse bag filter:
检查各联接件是否紧固,若有松动应立即拧紧。 1. Check whether the joints are tight, and tighten them immediately if they are loose.
检查各气动元件是否可靠。 2. Check whether each pneumatic component is reliable.
检查卸料阀、螺旋输送机是否完好。 3. Check whether the discharge valve and screw conveyor are intact.
Second, start-up operation:
发现排风口含尘浓度增大时,应检查滤袋是否破漏,检查时,先停系统风机,然后打开上部的检修门,观察袋口有积灰的,说明该袋破漏,应予更换或修补。 1. When the dust concentration in the exhaust vent is increased, check whether the filter bag is leaking. During the inspection, stop the system fan first, then open the upper inspection door, and observe that there is dust on the bag mouth, indicating that the bag is leaking. Should be replaced or repaired.
压气气源经调压阀调压,调至0.2~0.35MPa2. The pressure of the compressed air source is adjusted to 0.2 ~ 0.35MPa by the pressure regulating valve.
严格控制除尘器入口温度,防止滤袋被烧坏(滤袋为针刺毡,允许温度为120 ℃)。 3. Strictly control the inlet temperature of the dust collector to prevent the filter bag from being burned (the filter bag is needle felt and the allowable temperature is 120 ℃).
经常观察电磁阀和脉冲阀是否均正常工作,如发现个别无操作动作,应检查电磁阀和脉冲阀的接线,及时检修. 4. Frequently observe whether the solenoid valve and the pulse valve are working normally. If you find that there is no operation, you should check the wiring of the solenoid valve and the pulse valve for timely maintenance .
脉冲阀的膜片是易损件,如发现个别脉冲阀失去压气喷吹的声音时(或有漏气的声音时)应立即检查脉冲阀,更换损坏的膜片。 5. The diaphragm of the pulse valve is a wearing part. If you find that the pulse valve loses the sound of compressed air injection (or the sound of air leakage), you should immediately check the pulse valve and replace the damaged diaphragm.
从上部更换滤袋,打开检修门,从上面抽出骨架,脏袋投入箱内,由灰斗人孔门取出。 6. Replace the filter bag from the top, open the maintenance door, pull out the skeleton from above, put the dirty bag into the box, and take it out through the ash manhole door. A similar filter bag can be installed, and the bag mouth must be tightly sealed. Please note: Poor sealing of the bag mouth will affect the dust removal rate.
Dust collector equipment
Dust collector equipment
Industrial dust removal equipment manufacturers_Dongguan Yuchen Machinery Technology Co., Ltd. Copyrightn 2013 Sitemap visits: [ Baidu Statistics ]
Manufacturer of dust removal equipment_Telephone : 0769-8125 6298/81256299 Contact person : Ms. Xie / 13922901739 Sales person of industrial dust removal equipment: Mr. Wang / 13600259680
粤ICP备13067491号-2 * Our company is a dust removal equipment manufacturer integrating scientific research, development and manufacturing. * Technical Support: Dongguan Website Construction [ Background Management ] [ Email Login ] Guangdong ICP No. 13067491-2
必赢真人娱乐 七乐彩 星力捕鱼 欢乐拼三张