⎝⎛足球正网开户⎞⎠

Dongguan Yuchen Machinery Technology Co., Ltd. Industrial dust removal equipment manufacturers provide industrial dust extraction equipment, dust collector equipment, industrial dust collector equipment, grinding dust removal equipment, polishing dust removal equipment, workshop dust removal equipment, and provide a complete set of design solutions for workshop dust treatment plant dust treatment Quotation, see on-site service
Dongguan Yuchen Industrial Dedusting Equipment Manufacturer
Provide dust removal plan for grinding and polishing dust removal equipment workshop
Unified national service hotline:
0769-81256298 400-622-6298 0769-81256298

What to do when the industrial dust collector suddenly stops


When using industrial dust removal equipment to treat industrial dust suddenly stop or cannot start, you should first check the dust collector power line and other problems. 电机是否损坏,如这些有烧断或损坏要立即更换就可以排除。 It also includes the power switch and the motor control part, including whether the fuse of the dust removal equipment is blown, whether the power switch is damaged , whether the motor is damaged , if these are blown or damaged, they can be replaced immediately if they are replaced. If the power cord of the dust collector is not in good contact or the motor leads are loose, you need to reconnect it to start.

If you encounter a problem with the bag filter's high resistance or poor ventilation, and the solution:

) 压缩空气压力大大低于除尘器运行压力额定值。 ( 1 ) The compressed air pressure is much lower than the dust collector operating pressure rating.

) 卸灰阀锁风不好,有漏风现象。 ( 2 ) The ash discharge valve is not properly locked and leaks.

The solution is as follows:

) 调节合适的压缩空气的压力。 ( 1 ) Adjust the pressure of the appropriate compressed air.

) 立即停机检修卸灰阀或更换新品。 ( 2 ) Immediately stop the ash discharge valve or replace it with a new one.

Reasons for solenoid pulse valve normally closed:

) 控制仪损坏。 ( 1 ) The controller is damaged.

) 电磁阀失灵或排气孔被堵。 ( 2 ) The solenoid valve is malfunctioning or the exhaust hole is blocked.

) 膜片破损。 ( 3 ) The diaphragm is damaged.

Solution:

) 更换控制仪。 ( 1 ) Replace the controller.

) 检修或更换电磁阀。 ( 2 ) Repair or replace the solenoid valve.

) 更换膜片。 ( 3 ) Replace the diaphragm.

The reason why the electromagnetic pulse valve is always open:

) 电磁阀不能关闭。 ( 1 ) The solenoid valve cannot be closed.

) 小节流孔完全堵塞。 ( 2 ) The small orifice is completely blocked.

) 膜片上的垫片松脱漏气,检修或更换电磁阀,清除节流孔中污物,重新安装脉冲阀,装好垫片,更换失效弹簧。 ( 3 ) The gasket on the diaphragm loosens air leakage, repair or replace the solenoid valve, remove the dirt in the orifice, reinstall the pulse valve, install the gasket, and replace the failed spring.

如需要了解更多详情请咨询全国服务热线:400-622-6298. The above are the common problems of industrial dust collectors in daily work.For more details, please consult the National Service Hotline : 400-622-6298.

Dust collector equipment
Dust collector equipment
Industrial dust removal equipment manufacturers_Dongguan Yuchen Machinery Technology Co., Ltd. Copyrightn 2013 Sitemap visits: [ Baidu Statistics ]
Manufacturer of dust removal equipment_Tel : 0769-8125 6298/81256299 Contact person: Miss Xie / 13922901739 Sales person of industrial dust removal equipment: Mr. Wang / 13600259680
粤ICP备13067491号-2 * Our company is a dust removal equipment manufacturer integrating scientific research, development and manufacturing. * Technical Support: Dongguan Website Construction [ Background Management ] [ Email Login ] Guangdong ICP No. 13067491-2
必赢真人娱乐 七乐彩 星力捕鱼 欢乐拼三张