⎝⎛足球正网开户⎞⎠

Dongguan Yuchen Machinery Technology Co., Ltd. Industrial dust removal equipment manufacturers provide industrial dust extraction equipment, dust collector equipment, industrial dust collector equipment, grinding dust removal equipment, polishing dust removal equipment, workshop dust removal equipment, and provide a complete set of design solutions for workshop dust treatment plant dust treatment Quotation, see on-site service
Dongguan Yuchen Industrial Dedusting Equipment Manufacturer
Provide dust removal plan for grinding and polishing dust removal equipment workshop
Unified national service hotline:
0769-81256298 400-622-6298 0769-81256298

Troubleshooting method of stand-alone filter cartridge dust collector-yuchen technology


风量大,体积小,噪声低,移动方便,清灰,倒灰方便,操作简单运行稳定,适应范围广泛等优点。 The single machine dust collector series produced by Yuchen Technology has the advantages of low equipment input cost , large air volume , small volume , low noise , convenient movement , dust removal , convenient dust removal , simple operation, stable operation , and wide application range. The single-machine dust collector manufacturer will introduce the troubleshooting method of the single-machine dust collector .

单机滤筒式除尘器厂家

1.Host vibration :

A. When the impeller is rubbed, abnormal sounds and intense vibrations will occur at this time. The reason is that the fan casing or the impeller parts are deformed during storage, transportation, installation and use.

B. Deformation of the impeller, loose connection between the impeller and the shaft sleeve, deformation of the main shaft due to improper lifting, loosening of the fixed screw of the motor, and looseness of the fan's foot bolt.

2.Host fever :

After running for one hour at normal temperature, it is found that the motor temperature rises, it may be caused by one of the following reasons:

Excessive system resistance or unreasonable fan selection results in motor overload operation, excessive pipe network resistance coefficient or pipeline coefficient valve not open, motor bearing damage, small fit clearance, non-compliance, and low power supply voltage.

3.Air leakage from electromagnetic pulse valve

Causes: The air pressure balance hole of the electromagnetic pulse valve is blocked, the diaphragm of the electromagnetic pulse valve is damaged, and the compressed air contains more oil stains and water.

4.When the valve cannot be opened but the pilot part is moving

It is necessary to check whether the pressure of the air bag is too low and check for leaks.

5.Some valves are not working but others are normal .

You need to check the valve's wiring connections and coils for replacement parts.

6.All valves cannot be closed with air leakage and no pressure in the air bag .

It is necessary to check whether the inlet and injection ports of the valve are installed properly.

7.The valve closes slowly

Need to check the diaphragm orifice is blocked, clear the diaphragm orifice.

8.Some valves have leaking diaphragms.

It is necessary to check whether there are impurities on the valve which cause damage to the moving iron core. If the moving core is stuck, clean the diaphragm. If you check the completeness of the diaphragm, check the moving iron core and gas plug. Replace the parts in time.

9.The coil is hot and burned

长时间通电,并检查控制系统的工作情况。 Reason : Power on for a long time and check the operation of the control system.

10.When there is voltage but the valve does not work

Need to check the diaphragm valve is damaged or the orifice is blocked, and replace the parts in time.

11, the ambient temperature is low, the valve is leaking or cannot be opened ?

环境温度过低或者阀有冻结现象,注意保温。 Cause : The ambient temperature is too low or the valve is frozen. Pay attention to heat preservation.

Dust collector equipment
Dust collector equipment
Industrial dust removal equipment manufacturers_Dongguan Yuchen Machinery Technology Co., Ltd. Copyrightn 2013 Sitemap visits: [ Baidu Statistics ]
Manufacturer of dust removal equipment_Tel : 0769-8125 6298/81256299 Contact person: Miss Xie / 13922901739 Sales person of industrial dust removal equipment: Mr. Wang / 13600259680
粤ICP备13067491号-2 * Our company is a dust removal equipment manufacturer integrating scientific research, development and manufacturing. * Technical Support: Dongguan Website Construction [ Background Management ] [ Email Login ] Guangdong ICP No. 13067491-2
必赢真人娱乐 七乐彩 星力捕鱼 欢乐拼三张