|Industrial dust treatment equipment series|
|Welding fume exhaust gas treatment series|
|Grinding polishing dust removal equipment|
|Stand-alone dust collector|
|Spiral duct and accessories series|
The ash storage bin of the dust removal equipment is a necessary device for storing dust in the moving dust system of the dust removal equipment , and is composed of the equipment body and auxiliary equipment. The main body of the dust removal equipment includes the lower ash hopper, the main body, the ladder, the maintenance platform, the decomposition device, and the exhaust device. The auxiliary equipment includes a plug valve, a lower ash valve, a dust absorption device, a spray device, and a dust truck.
The design of the ash storage bin of the dust removal equipment is as follows:
：贮灰仓的存灰比例按 24-48h 粉尘量来算，或者按运尘车 1-2 次运输的粉尘量琮确定。 1 : The ash storage ratio of the ash storage bin is calculated according to the amount of dust in 24-48h , or determined according to the amount of dust transported by the dust truck 1-2 times
：贮灰仓大多数除尘设备厂家都采用圆筒形，高度和直径相差不大，对零散粒的粉尘，灰仓可设计高点，对密度较大、黏性大、颗粒小的粉尘灰仓可设计低些。 2 : Most dust removal equipment manufacturers in ash storage bins use a cylindrical shape, with little difference in height and diameter. For scattered dust, the ash bin can be designed to have a high point. The warehouse can be designed lower.
：除尘设备贮灰仓的下灰斗角度应该按粉尘安息角而决定，灰斗夹角度数普遍比粉尘安息角小 2 ° -5 °。 3 : The angle of the lower ash bucket of the ash storage bin of the dust removal equipment should be determined according to the dust repose angle. Generally, the number of the angle of the hopper clamp is 2 ° -5 ° smaller than the dust repose angle .
：输送粉尘的车用罐式卡车时贮灰仓下面应设计 3GY 型粉尘没有粉尘下灰时，要防止粉尘外泄对污染造成环境，用下灰阀送往致运尘车下灰时，在下灰阀的周围要设计吸尘罩。 4 : For tank trucks that transport dust, a 3GY type of dust should be designed under the ash storage bin. When the dust is not ashed by dust, the dust should be prevented from leaking to the environment. Use the ash valve to send it to the dust truck. Design a dust extraction hood around the lower ash valve.
The problem of dust pollution in the workshop can refer to: How to improve the dust in the workshop
：工程师在量贮灰仓粉尘数量多少的料位计应设 2 个： 1 个高料位计和 1 个低料位计，料位计的分类有三种形式，分别是电容式、阻旋式、振棒式等等。 5 : The engineer should set two level gauges for the amount of dust in the ash storage bin : 1 high level gauge and 1 low level gauge. There are three types of level gauges, which are capacitive and rotational resistance. Style, vibrator style, etc.
：防棚灰设计有空气冲突和振动电机两种，对黏和小的粉尘性质以以空气冲突设计好。 6 : The anti-shed ash design has two types of air collision and vibration motor. It is good to design air collision for sticky and small dust properties.
When the ash storage bin of the dust removal equipment unloads the ash to the conveying equipment, it should try to choose the transportation equipment that generates secondary dust.