|Industrial dust treatment equipment series|
|Welding fume exhaust gas treatment series|
|Grinding polishing dust removal equipment|
|Stand-alone dust collector|
|Spiral duct and accessories series|
Yuchen Machinery Dongguan woodworking dust removal equipment manufacturer's woodworking dust collector equipment has high purification efficiency, small size and low cost. It solves the problem of dust pollution in workshops for many furniture factories and woodworking factories in Dongguan, and provides wood chips for many woodworking production workshops in Dongguan. Dust treatment provides guidance and plans on site and quotation.
The woodworking dust removal equipment produced by Dongguan woodworking dust removal equipment manufacturers is suitable for dust management in the production of woodworking grinding and polishing workshops. For woodworking workshop processing equipment such as: grinding machines, cutting, and workers' grinding equipment, such as material grinding, polishing, cutting, sanding, etc. Disposal of wood dust and fine dust, and the recyclable effect on materials that can be used for the second time.
Dongguan woodworking dust removal equipment remind you to choose woodworking dust removal equipment Note:
：木工除尘设备厂家工程师看现场时要对木工加工车间的粉尘量、气体温度、粉尘性质、气体粉尘的浓度、排放出来的标准做相关的技术测量。 1 : When the engineer of the woodworking dust removal equipment manufacturer sees the scene, he must make relevant technical measurements on the amount of dust, gas temperature, dust properties, gas dust concentration, and emission standards in the woodworking processing workshop.
：木工除尘器设备的吸风口、排风口和风道、箱体之间的连接处要做到不漏风、粉尘不可以泄漏的情况以下，不能影响到整体除尘净化的效果。 2 : The connection between the air inlet, air outlet, air duct, and box of the woodworker's dust collector must be airtight and the dust must not be leaked. It must not affect the overall dust removal and purification effect.
：东莞木工除尘设备意见在设备装配完工后，在开机之前缓慢加温不要高于 150 度，最好保持这个温度使用 48 个小时之后在开始正常的使用，比较大功率的木工除尘设备在使用之前，要注意先把排气阀打开，并把里面的多余的水分放完。 3 : Opinions on Dongguan woodworking dust removal equipment. After the equipment is assembled, slowly warm it up to 150 degrees before starting . It is best to keep this temperature for 48 hours before starting normal use. More powerful woodworking dust removal equipment is in use. Before that, you should pay attention to opening the exhaust valve and letting out excess water in it.
：除尘器设备在运行之前，要先打开引风机，在开鼓风机，关机之前先关掉鼓风机。 4 : Before the dust collector equipment is running, the induced draft fan must be turned on, and the blower must be turned off before the blower is turned off.
：整套木工除尘设备设计时要保证灵活严密，不要出现漏气漏风的情况。 5 : The whole set of woodworking dust removal equipment must be designed to be flexible and tight, so as not to leak air or air.
Dongguan woodworking dust removal equipment operation principle
The sawdust dust generated by the woodworking workshop during processing is sucked into the dust collector through the air duct through the air duct. The sawdust dust is absorbed by the dust bag to the outside of the filter bag, and the clean gas is discharged from the exhaust pipe above the fan. The wood dust dust isolated on the outside of the cloth bag is shaken down by the pulse automatic dust cleaning system device, and the wood dust dust dropped down is discharged from the ash bucket of the lower box.
More related content: Woodworking dust removal equipment
Dongguan woodworking dust removal equipment case picture:
Dongguan Yuchen Dust Removal Equipment Manufacturer has been focusing on the field of woodworking dust removal equipment for many years, solving various environmental pollution problems caused by woodworking for the Pearl River Delta and other regions. If you need to consult solutions, understand prices, or have more questions about dust removal equipment 400-622-6298 Please contact us, we will be happy to provide you with the best service!