⎝⎛足球正网开户⎞⎠

Dongguan Yuchen Machinery Technology Co., Ltd. Industrial dust removal equipment manufacturers provide industrial dust extraction equipment, dust collector equipment, industrial dust collector equipment, grinding dust removal equipment, polishing dust removal equipment, workshop dust removal equipment, and provide a complete set of design solutions for workshop dust treatment plant dust treatment Quotation, see on-site service
Dongguan Yuchen Industrial Dedusting Equipment Manufacturer
Provide dust removal plan for grinding and polishing dust removal equipment workshop
Unified national service hotline:
0769-81256298 400-622-6298 0769-81256298

Design points of small ventilation and dust removal equipment


Small-scale exhaust dust removal equipment can deal with some small emission pollution problems. Generally, it can be placed in the workshop for in-situ dust removal. Its advantages are small footprint and low investment cost, which is very suitable for some small workshops such as machining, die-casting, grinding and polishing. The area of emission control, the design points of small extraction and dust removal equipment are generally divided into the following points:

 

小型抽风除尘设备 里面的空气的流动速度,一般选取在0 1: The flow speed of the air in the small-scale exhaust dust removal equipment is generally selected at 0 . -3 4-3 . s 之间这个数字。 This number is between 0m / s .

 

小型抽风除尘设备 的规格以小、长、宽的设计要点最好,如果除尘设备高度太高,那么除尘设备上面的粉尘到下面的时间用时长,粉尘一般没有落到最下面就被气流带走了。 2: The specifications of the small exhaust dust removal equipment are best with small, long and wide design points. If the height of the dust removal equipment is too high, the time from the dust above the dust removal equipment to the bottom takes a long time, and the dust generally does not fall to the bottom and is airflowed. bought. After the size of the dust removal equipment is determined, the width will widen, and the total height will decrease; so the design points of the dust removal equipment can make the dust fall.

 

小型抽风除尘设备 里面可以在设计要点里面设计挡板,一般采取平面隔板降低室高度形成多层除尘设备以达到更好的除尘效果。 3: The baffle can be designed in the design points in the small-scale exhaust dust removal equipment . Generally, a flat partition is used to reduce the height of the room to form a multi-layer dust removal equipment to achieve better dust removal effects.

 

小型抽风除尘设备 设计要点要点中偶尔有不能用计算尺寸确定设计要点,可以视车间具体的布置在考虑如何设计。 4: There are occasions when designing the main points of small air extraction and dust removal equipment . The calculation points cannot be used to determine the design points. Depending on the specific layout of the workshop, how to design is considered.

 

5: The dust falling inside the equipment can be designed to install and remove the device, so as to better ash and clean the ash.


小型抽风除尘设备设计要点


小型单机除尘器 Related products: Small single machine dust collector

 

小型抽风除尘设备 大多数只能捕集大于直径40-50m 粉尘颗粒,而且除尘效果一般,所以除尘设备不仅要在除尘效率要求不高或多种除尘的一般除尘的场合被采用。 6: Most small dust extraction equipment can only capture dust particles larger than 40-50m in diameter , and the dust removal effect is average, so the dust removal equipment must not only be used in general dust removal occasions where the dust removal efficiency is not high or a variety of dust removal is required.

 

小型抽风除尘设备 设计要点可以参考粉尘的数量、车间空间位置大小和除尘效率在要求除尘设备厂家设计成不同的节构和外形。 7: The main points of the design of the small-sized air extraction and dust removal equipment can refer to the amount of dust, the size of the workshop space, and the dust removal efficiency. The dust removal equipment manufacturers are required to design different structures and shapes.

 

Working principle of small air extraction and dust removal equipment:

 

表面的粉尘抖落下来,落在抽屉中的粉尘由人工拉出清除。 The dust gas in the workshop enters the cabinet of the small-sized exhaust dust removal equipment, and is filtered by a filter cartridge. The dust is isolated on the outer surface of the filter cartridge. The clean gas enters the fan through the center of the filter cartridge, and is directly sucked out from the fan. With the increase of the running time of the exhaust dust removal equipment, the dust adhered to the outside of the filter cartridge has also increased, and the resistance of the filter cartridge has increased accordingly, which has affected the dust removal efficiency. The dust on the surface of the tube shakes down, and the dust in the drawer is manually pulled out to remove it.  


小型抽风除尘设备设计要点


More small dust removal equipment products: stand-alone dust collector

 

提供看现场出设计方案、报价等相关服务,欢迎您致电400-622-6298 ,我司为您提供更多详细的 小型抽风除尘设备设计要点! More models, operating principles, and prices of small dust extraction equipment need our dust removal equipment manufacturers to provide on-site design solutions, quotations and other related services. You are welcome to call 400-622-6298 . Our company will provide you with more detailed information. The main points of the design of small-scale air extraction and dust removal equipment!


Dust collector equipment
Dust collector equipment
Industrial dust removal equipment manufacturers_Dongguan Yuchen Machinery Technology Co., Ltd. Copyrightn 2013 Sitemap visits: [ Baidu Statistics ]
Manufacturer of dust removal equipment_Tel : 0769-8125 6298/81256299 Contact person: Miss Xie / 13922901739 Sales person of industrial dust removal equipment: Mr. Wang / 13600259680
粤ICP备13067491号-2 * Our company is a dust removal equipment manufacturer integrating scientific research, development and manufacturing. * Technical Support: Dongguan Website Construction [ Background Management ] [ Email Login ] Guangdong ICP No. 13067491-2
必赢真人娱乐 七乐彩 星力捕鱼 欢乐拼三张