⎝⎛足球正网开户⎞⎠

Dongguan Yuchen Machinery Technology Co., Ltd. Industrial dust removal equipment manufacturers provide industrial dust extraction equipment, dust collector equipment, industrial dust collector equipment, grinding dust removal equipment, polishing dust removal equipment, workshop dust removal equipment, and provide a complete set of design solutions for workshop dust treatment plant dust treatment Quotation, see on-site service
Dongguan Yuchen Industrial Dedusting Equipment Manufacturer
Provide dust removal plan for grinding and polishing dust removal equipment workshop
Unified national service hotline:
0769-81256298 400-622-6298 0769-81256298

Maintenance method of industrial dust removal equipment


Industrial dust removal equipment is generally used in power plants, woodworking factories, foundries, furniture factories, workshops, polishing and dust removal, and other industries. At the same time, it can be used in industrial dust removal, industrial dust extraction, grinding wheel grinding, chemical pharmaceutical, machinery processing and other industries. Dust removal equipment can deal with the pollution emissions of enterprises, but if we do not pay attention to maintenance when we use it, we will find that the dust removal efficiency of the equipment starts to decline slowly. Today Yuchen dust removal equipment manufacturers will introduce the maintenance methods of industrial dust removal equipment. .


工业除尘设备的保养方法

 

The maintenance method of industrial dust removal equipment is as follows:

 

,每次开机运行前检查一下风机轴承箱的机油油面线是否正常。 1. Check whether the oil level line of the fan bearing box is normal before each start-up operation. If the oil bottom is found on the oil level line, it should be added to the oil level line standard in time. And regularly check the tightness of the turning triangle between the fan and the electric motor. 6kg, 并打开供气阀门使压缩空气进入除尘器气包内待用。 The air pressure of the compressed air required for the dust blower to blow back the dust must not be less than 6kg, and the air supply valve is opened to allow the compressed air to enter the dust bag of the dust collector for use.

 

、开启脉冲控制仪电源开关,当听到有定期放气的冲击声后,脉冲控制仪工作为正常。 2. Turn on the power switch of the pulse controller. When you hear the impact sound of regular deflation, the pulse controller works normally.

 

Then turn on and start the spiral unloader and the unloader. (The above are preparations before using the vacuum system)

 

、上班使用先开启气力收尘输送系统主风机。 3. Turn on the main fan of the pneumatic dust collection and conveying system before using at work. 2 3 分钟后,再开启使用每个车间的吸尘系统风机。 Wait for 2 to 3 minutes of dry running before turning on the fans of the vacuum system in each workshop.

 

、下班时气力收尘输送系统风机最后关闭,关闭前需空运行 5 8 分钟。 4. The fan of the pneumatic dust collection and conveying system will be turned off at the end of work. It needs to be run for 5-8 minutes before closing . (Because the conveying distance is long, prevent the dust from staying in the air duct and blocking it, causing malfunction)

 

、开启每个车间的吸尘系统风机前需将吸尘系统内的吸风口阀门全部开启。 5. Before turning on the fan of the dust collection system in each workshop, all the air inlet valves in the dust collection system must be turned on. It is strictly forbidden to open the fan suction system under the condition that the air inlet valve is fully closed to cause system damage and accidents.

 

、每个车间上班时先开启吸尘系统待空载运行 2 3 分钟后开启木工设备运作,不运作的木工设备可关闭吸风口的阀门。 6. When each workshop is at work, first turn on the vacuuming system and wait for 2 to 3 minutes of no-load operation. Then turn on the woodworking equipment. Non-working woodworking equipment can close the air inlet valve.

 

、每次下班前关闭全部运作的木工设备,待吸尘系统空载运行 3 5 分钟后再关闭风机。 7. Shut down all the woodworking equipment before work every time, and then turn off the fan after the vacuum system is running for 3 to 5 minutes with no load . . Due to the long distance of the dust suction duct in the workshop, dust is prevented from staying blocked in the air duct, causing malfunction .


工业除尘设备的保养方法


How much is a set of dust removal equipment?

 

、在使用过程中严禁误将大木块、回絲、手套、手砂皮及其它物料吸入系统内,以免 8. It is strictly forbidden to suck large wooden blocks, loops, gloves, sand leather and other materials into the system during use, so as to avoid

Causes fan impeller damage, vibration, and noise.

 

、气力收尘系统料仓下料口应派专人负责木屑装包岀料,以免木屑堆起来塞住除尘器 9 、 Pneumatic dust collection system, the material outlet of the silo should be assigned to be responsible for the packing of wood chips, so as not to pile up wood chips and plug the dust collector

 

Unloader discharge port, causing damage to the entire system.

 

、为确保吸风效果除尘器内的过滤布袋建议使用壹年后更换一次。 10. In order to ensure the suction effect, the filter bag in the dust collector is recommended to be replaced after one year.

 

、室外除主器、及钢支架、风机、风管每一年作防腐保养一次。 11. Outdoor anti-corrosion and mainframe, and steel brackets, fans, and ducts are subject to anticorrosive maintenance once a year.

 

12. The use of the dust removal system in each workshop requires a special person to be responsible for opening, closing, and implementing special person maintenance.


工业除尘设备的保养方法


More recommendations: characteristics and classification of dust removal equipment

 

的官网查询更多相关的信息! Industrial dust removal equipment is also a consumable product. If we do not maintain it often, it will shorten its life, air leakage everywhere, and some failures with low dust removal efficiency. Therefore, we must pay attention to its maintenance when using it. The longer the equipment can be used for a longer time, the better the dust removal efficiency. For more maintenance methods of industrial dust removal equipment , you can go to the official website of our dust removal equipment manufacturer for more relevant information!

 

Dust collector equipment
Dust collector equipment
Industrial dust removal equipment manufacturers_Dongguan Yuchen Machinery Technology Co., Ltd. Copyrightn 2013 Sitemap visits: [ Baidu Statistics ]
Manufacturer of dust removal equipment_Tel : 0769-8125 6298/81256299 Contact person: Miss Xie / 13922901739 Sales person of industrial dust removal equipment: Mr. Wang / 13600259680
粤ICP备13067491号-2 * Our company is a dust removal equipment manufacturer integrating scientific research, development and manufacturing. * Technical Support: Dongguan Website Construction [ Background Management ] [ Email Login ] Guangdong ICP No. 13067491-2
必赢真人娱乐 七乐彩 星力捕鱼 欢乐拼三张