|Industrial dust treatment equipment series|
|Welding fume exhaust gas treatment series|
|Grinding polishing dust removal equipment|
|Stand-alone dust collector|
|Spiral duct and accessories series|
The dust removal equipment and mine dust collector of the mine are mainly used for filtering and treating the flue gas dust of the crusher, vibrating screen, belt conveyor transfer, mobile trolley and other dust in the ore dressing workshop. Our mine dust removal equipment is a production, manufacturing and installation integration Manufacturer.
How to choose mine dust removal equipment:
、每个出尘点都要有必要的密封进行紧密。 1. Each dust outlet must be tightly sealed as necessary.
、除尘器考虑安放和位置不可以影响工人操作习惯。 2. The placement and position of the dust collector must not affect the operating habits of workers.
、矿厂除尘设备器、选矿车间除尘设备、矿山滤筒除尘器排放浓度要求≤ 30mg/Nm3 3.Requirements for the emission concentration of dust removal equipment in mining plants, dust removal equipment in ore dressing workshops, and dust collectors in mine cartridges ≤ 30mg / Nm
、一般选用脉冲清灰系统 . 4.Pulse dust cleaning system is generally used .
、除尘器选用滤筒过滤，并设有滤袋检漏设备 5. The dust collector is filtered by a filter cartridge and equipped with a filter bag leak detection device
、除尘器卸灰到皮带运送机上。 6. The dust remover removes the ash to the belt conveyor.
、操控柜设置成有主动和手动交换操控，当自动操控时发生事故的时候，可以选用手动操控。 7. The control cabinet is set to have active and manual exchange control. When an accident occurs during automatic control, manual control can be selected.
The dust removal equipment of the mine is mainly composed of the following parts:
：箱体：包含袋室、净空气、多孔板、滤筒、检修门，箱体规划耐压为 5000pa 。 1 : Box: Contains bag room, clean air, perforated plate, filter cartridge, and maintenance door. The planned pressure resistance of the box is 5000pa .
：出风体系：包含风机、风机配用电机。 2 : Air outlet system: Contains fan and fan-equipped motor.
：喷吹体系：包含气包、喷吹管、脉冲阀、操控仪。 3 : Blowing system: Including air bag, blowing pipe, pulse valve and controller.
Related recommendation: Nine precautions for dust removal equipment
Principles of dust removal equipment in mining plants
The induced dust fan of the dust removal equipment of the mine plant introduces the dust from the dust producing point of the ore plant into the middle casing from the air inlet. The clean gas passes through the filter cylinder into the clean room and is discharged from the clean air outlet. The dust is blocked on the outer wall of the filter bag. With the extension of the moment, the dust adsorbed on the filter cartridge became thicker and thicker, and the resistance of the filter bag became larger and larger. At this moment, the pulse controller announced a signal and the program actively controlled the opening and closing of each pulse valve, so that the high-pressure gas source was injected. The holes and Venturi tubes erupted into the filter bag. Due to the effect of high-pressure gas, the filter cartridge swelled sharply and caused shock oscillations, so that the dust adsorbed on the external surface of the filter cartridge was shaken into the ash bucket and discharged from the ash conveying tissue.
The final assembly of the dust removal equipment in the mine is completed, and each rolling system part is sensitive. The subordinate equipment and the control system of each department should be functional and reliable.
The design requirements of the dust removal equipment of the mine are as follows:
除尘器排放浓度必须保证在环保排放标准以内，作业环境粉尘浓度在卫生标准以内； (1) The dust concentration of the dust collector must be within the environmental protection emission standards and the dust concentration in the operating environment is within the hygienic standards;
粉尘污染治理过程，不能出现二次杨尘，也不能转移为其他污染。 (2) During the process of dust pollution control, secondary poplar dust cannot appear, nor can it be transferred to other pollution.
除尘器噪声不可以超过国家卫生标准和环保标准。 (3) The noise of the dust collector must not exceed the national health standards and environmental protection standards.
除尘器收下粉尘可以配套综合利用措施。 (4) The dust collected by the dust collector can be equipped with comprehensive utilization measures.
Related Recommendations: Dust Collector
400-622-6298 ，我们可根据您的要求，设计制造高效、实用和可靠的各种非标除尘器设备！ For more models , working principles, and prices of dust removal equipment in mining plants , please call Yuchen Dust Removal Equipment Manufacturer at 400-622-6298 . We can design and manufacture various non-standard dust remover equipment according to your requirements!