|Industrial dust treatment equipment series|
|Welding fume exhaust gas treatment series|
|Grinding polishing dust removal equipment|
|Stand-alone dust collector|
|Spiral duct and accessories series|
The metallurgy industry cannot be separated from the intermediate frequency furnace during production. The metallurgy intermediate frequency furnace generates a lot of smoke during exercise, feeding and tapping, especially during exercise. The intermediate frequency furnace dust removal equipment Generally, a dust removal hood is installed on the top to deal with the smoke and dust generated during exercise. This method is also the most effective and economical and feasible dust removal method. The following describes the model and operating principle of the intermediate frequency furnace dust removal equipment .
The model and operating principle of the intermediate frequency furnace dust removal equipment are as follows:
Intermediate frequency furnace dust removal equipment is used to collect and manage flue gas and dust during exercise. There are three types of dust collectors suitable for intermediate frequency furnace furnace dust removal: bag dusters, wet dust collectors, electrostatic precipitators, collectively referred to as intermediate frequency furnaces. Dust removal equipment.
1: Model of IF furnace dust removal equipment
The intermediate frequency bag filter is composed of a shell, a filter bag, an ash hopper, an ash discharge device, a support and a pulse ash cleaning system.
When the gas with smoke and dust enters the dust collector from the air inlet, it first encounters the inclined partition in the center of the air inlet, and the airflow turns to flow into the ash hopper, and the airflow speed becomes slower because of the gravity sedimentation effect, which makes the gas rough. The particulate dust falls directly into the ash hopper, which has the effect of pre-dust collection. The airflow entering the ash hopper then folds upwards, passes through a filter bag with a metal frame inside, and the dust is captured on the outside of the filter bag. The purified gas enters the clean room on the upper part of the filter bag room and is collected in the air outlet pipe for discharge. .
2: Operating principle of dust removal equipment for intermediate frequency furnace
The intermediate frequency furnace dust collector is economical and practical, with simple structure, simple device and convenient repair. 120 摄氏度左右，除尘效果可达 99% ，如有特别用处可提供耐温，耐腐蚀滤袋的除尘器。 It is mainly used for dust collection at small dusting points. The machine uses polyester bags. The inlet temperature is about 120 degrees Celsius, and the dust removal effect can reach 99% . If there is a special use, a temperature-resistant and corrosion-resistant filter bag can be provided.
The intermediate frequency furnace flue gas capture system consists of a low-position mobile dust collection hood, feeding equipment, tapping equipment and dust removal equipment. The low-position mobile dust cover completely covers the operation channels and tapping pits, so that the production process of the intermediate frequency furnace is fully performed in the low-position mobile dust cover, which completes the useful capture of the entire process of smoke. ; 出钢时，中频炉渠道翻转直接出到出钢轨迹平车上的钢包里，出钢进程在烟罩内完结，战胜了部分集尘罩出钢时烟气部分外漏的状况。 When feeding, the material is fed through the feeding equipment, and the material is filled up several times according to the production requirements, which solves the problem of difficult capture of flue gas during the feeding of the vehicle. In the ladle, the tapping process was completed in the hood, which overcomes the situation that some of the flue gas leaked out when some of the dust collecting hoods were tapping.
Related recommendation: Boiler dust removal equipment technical transformation plan
3: Features of IF furnace dust removal equipment
The air inlet of the dust removal equipment of the intermediate frequency furnace is set on the ash hopper. After the airflow enters the ash hopper, the baffle at the end of the duct is firstly touched. Each dust collecting room cleans dust in turn at a given time distance. Each dust collecting room is equipped with a raising valve, which is closed during dust cleaning to block the filtered air flow passing through the dust collecting room. Spray water-free, oil-free, high-pressure clean air into the filter bag to remove dust on the outside of the filter bag. The pulse blowing width and dust cleaning cycle of each dust collection room are successively performed by a dedicated dust cleaning degree controller.
Related recommendation: Boiler bag dust removal equipment
确保对每一个客户所提供的中频炉除尘设备除尘风量需求计算精准，有着非常严格的计算标准，中频炉除尘设备出厂前，由出厂检测员测量除尘器设备燥音和风速，达标后才可以出厂，确保每一台除尘器设备质量过关。 Yuchen dust removal equipment manufacturers ensure accurate calculation of the dust removal air flow requirements of the IF furnace dust removal equipment provided by each customer, with very strict calculation standards. Before leaving the IF furnace dust removal equipment, the factory inspectors measure the noise and wind speed of the dust collector equipment. Only after reaching the standard can we leave the factory to ensure the quality of each dust collector. We are not only seeking honor, but also seeing the recognition of each customer. More models and operating principles of IF furnace dust removal equipment are welcome to call us!