⎝⎛足球正网开户⎞⎠

Dongguan Yuchen Machinery Technology Co., Ltd. Industrial dust removal equipment manufacturers provide industrial dust extraction equipment, dust collector equipment, industrial dust collector equipment, grinding dust removal equipment, polishing dust removal equipment, workshop dust removal equipment, and provide a complete set of design solutions for workshop dust treatment plant dust treatment Quotation, see on-site service
Dongguan Yuchen Industrial Dedusting Equipment Manufacturer
Provide dust removal plan for grinding and polishing dust removal equipment workshop
Unified national service hotline:
0769-81256298 400-622-6298 0769-81256298

Stainless steel grinding and polishing dust treatment plan


Stainless steel grinding and polishing dust treatment solutions generally use wet duster treatment methods to treat stainless steel grinding and polishing dust, because stainless steel grinding and polishing dust is an explosive type of dust, and wet water treatment can effectively prevent dust from exploding. The next possibility is the introduction of the stainless steel grinding and polishing dust treatment program.


不锈钢打磨抛光粉尘治理方案

 

Features of Wet Stainless Steel Sanding and Polishing Dust Treatment Program:

 

、全程湿式处理(粉尘进入风机前、后都是湿式),安全性高; 1. Full wet processing (dust is wet before and after the dust enters the fan), high safety;

、粉尘渣主集中在三级过滤水池,需要定期清渣; 2. The dust and slag are mainly concentrated in the three-stage filter pond, and regular slag removal is required;

、离心风机叶片上会积尘较多(湿式处理的粉尘先进入风机),离心风机维护频次会增加; 3. There will be more dust accumulation on the centrifugal fan blade (wet-treated dust enters the fan first), and the maintenance frequency of the centrifugal fan will increase;

、由于湿式处理的粉尘先进行离心风机,选用离心风机时功率会稍小。 4. As the wet-processed dust is subjected to a centrifugal fan first, the power will be slightly smaller when a centrifugal fan is selected.

、需要加装水量水压监测报警装置,并且与抛光电机联动;加装风机先启动 10 分钟后 5. It is necessary to install a water pressure and pressure monitoring alarm device, and it is linked with the polishing motor; after installing the fan, start it for 10 minutes.


不锈钢打磨抛光粉尘治理方案

 

Technical points of wet stainless steel grinding and polishing dust treatment program:

 

1. If the polishing and grinding process shares a factory building with other processes, the polishing and grinding process should be set up against the external wall in the factory building and separated from other areas by solid walls;

 

2. The polishing workshop should have two or more safety exits, at least one of which should lead to a non-explosive danger area;

 

所有产尘点均应装设吸尘罩,风管中不应有粉尘沉降;除尘器主风管风速应大于 23m/s 3. All dust production points should be equipped with dust suction hoods, and there should be no dust settlement in the air ducts; the wind speed of the main air duct of the dust collector should be greater than 23m / s ;

 

4. Hydrogen removal devices need to be set above the wet dust removal tower and wet filter pond (the dust removal will be closed when the dust removal is working normally, and it will be automatically opened when the dust removal is stopped);

 

采用干砂、专用干粉等 D 类金属火灾灭火器材灭火; 5. Use Class D metal fire extinguishing equipment such as dry sand and special dry powder to extinguish the fire;

 

6. Polishing and polishing operations cannot be carried out in crossover with hot work;

 

7. Wastewater, waste gas and waste must be treated in accordance with relevant environmental protection standards.


Product introduction: Wet dust collector


不锈钢打磨抛光粉尘治理方案

 

Safety standard specification for wet stainless steel sanding and polishing dust treatment scheme

 

GB 15577 "Dust Explosion Safety Regulations" ( GB 15577 )

"Administrative Regulations of Guangdong Provincial Administration of Work Safety on Dust Explosion Safety of Metal Product Processing Enterprises (Trial)"

AQ 4272 "Technical Specification for Explosion-proof Safety of Aluminum and Magnesium Products in Mechanical Processing" ( AQ 4272 )

AQ4273 "Safety Technical Specification for Dust Removal System for Danger of Dust Explosion" ( AQ4273 )

GB/T 17919 "Guide to Explosion Protection of Dust Collectors for Dust Explosion Hazardous Locations" ( GB / T 17919 )

1 部分通用要求》( GB 12476.1 "Combustible dust environment electrical equipment part 1 general requirements" ( GB 12476.1 )

2 部分:选型和安装》( GB 12476.2 "Electrical Equipment for Combustible Dust Environment Part 2 : Selection and Installation" ( GB 12476.2 )

GB 12158 "General Guidelines for the Prevention of Static Electricity Accidents" ( GB 12158 )

GB 50140 "Code for Design of Fire Extinguisher Configuration" ( GB 50140 )

GB50016 2006 "Code for Fire Protection in Building Design" ( GB50016 2006 )




Product more information: Stainless steel polishing and dust removal equipment

 

,为您提供更多全面的不锈钢打磨抛光粉尘治理方案。 For more stainless steel grinding and polishing dust management solutions , prices and other issues, please call Yuchen Dust Removal Equipment Manufacturers to provide you with more comprehensive stainless steel grinding and polishing dust management solutions.

Dust collector equipment
Dust collector equipment
Industrial dust removal equipment manufacturers_Dongguan Yuchen Machinery Technology Co., Ltd. Copyrightn 2013 Sitemap visits: [ Baidu Statistics ]
Manufacturer of dust removal equipment_Tel : 0769-8125 6298/81256299 Contact person: Miss Xie / 13922901739 Sales person of industrial dust removal equipment: Mr. Wang / 13600259680
粤ICP备13067491号-2 * Our company is a dust removal equipment manufacturer integrating scientific research, development and manufacturing. * Technical Support: Dongguan Website Construction [ Background Management ] [ Email Login ] Guangdong ICP No. 13067491-2
必赢真人娱乐 七乐彩 星力捕鱼 欢乐拼三张