|Industrial dust treatment equipment series|
|Welding fume exhaust gas treatment series|
|Grinding polishing dust removal equipment|
|Stand-alone dust collector|
|Spiral duct and accessories series|
Some related introductions of stand-alone dust collector manufacturers (1) There are three types of stand-alone dust collectors used by the company, which are mature technology products of the company. The difference is that the latter two products are multi-machine combinations. Generally speaking, there is no problem with dust removal during shutdown, and the air volume and processing air volume are also Very large. In this case, cement plants usually use more pneumatic pulse bag filters. Although it has not been applied yet, only single machine dust removal has been performed, but it cannot be concluded that vibration dust removal is not as good as pulse dust removal or back blow dust removal. Mechanical vibration dust removal does not require closed air. The principle is simple and easy to learn and repair. No air blow in back blow is required Valve dust removal. It still has a place in bag dust removal technology. In the application selection, it is more suitable for the uf series stand-alone bag dust collector with small air flow and low dispersed dust concentration. Otherwise, centralized dust removal should be selected. Multiple dust collection points should be connected to the dust extraction hood, sharing large dust removal equipment, and stopping dust removal. . This will also cause problems such as large investment, uneven air volume distribution, and inconvenient management. This is not only a problem when using a single bag filter unit.
Some related introductions of stand-alone dust collector manufacturers (2) Resumption of ash removal and ash removal operation mode. As mentioned above, the result of non-stop dust removal can only be that the vacuum cleaner cannot work. Although the dust will escape instantly during the dust removal process, the number of dust removal times can be minimized on site, that is, the dust removal cycle must be re-determined according to the operating conditions. First set a u-shaped tube pressure gauge on the dust collector to measure the pressure difference between the inside and outside of the dust collector bag. If there is a dust removal controller, set the running time to a larger value and check the pressure rise after startup. When it reaches 1500-1900 pa, record the running time, that is, the dust removal distance time. It can also directly check the dust collection status of the dust collection point. Until it cannot be collected due to the increased dust collection resistance, which explains the dust removal. These methods can reduce the number of dust removals in some central areas, thereby maximizing working hours. No matter how long the dust removal distance is, each shift must be cleaned less once.
Some related introductions of stand-alone dust collector manufacturers (3) Strengthen equipment maintenance and timely treatment to prevent the problem from expanding. For the uf series stand-alone bag dust collector, the central vibration mechanism and filter bag that are prone to problems will be used. Note the shaking mechanism, each time Shake time should not exceed 30 seconds. Regularly check joint bearings and connecting rod bearings. These bearings are made of copper sleeves. Because the site is dusty and easy to wear, you must stop cleaning and refueling regularly. Open the inspection door regularly to check whether the filter bag is suspended Loose. The dust removal filter bag naturally stretches after using for a period of time. At this time, it should be re-tensioned. The method is to adjust the rocker to a certain position, remove the filter bag, and re-tighten the filter bag until it feels strong by hand. The tension level of each filter bag is similar. If the dust in the filter bag cannot be removed, manual cleaning should be stopped. If the bag is found to be damaged, it should be replaced in time.
Some related introductions of stand-alone dust collector manufacturers (4) When some users report that the shutdown of the ash removal or the process does not allow the shutdown of the ash removal, you can use the additional uf stand-alone bag dust collector of the same specification to combine two units to work in turn. Of course, this It depends on whether the website can be agreed. This is the vacuum cleaner that the company uses for the top of the warehouse. When the two machines are used together, the modification of the electronic control equipment should be stopped so that it can automatically control the rotation of the two equipment. Some large factories choose When using more but not ideal uf series stand-alone dust collectors, you can consider reassembling and using these devices, which can at least solve some local problems.
Some related introductions of stand-alone dust collector manufacturers (5) Generally speaking, the dust removal equipment is not as important as the host equipment, and the management is relatively loose. In fact, the dust removal equipment also needs to be managed. This management must first be reflected in the training of operation and maintenance personnel. Some The factory owner knows nothing about the dust removal equipment, but of course it is not easy to use.
After the above analysis, it can be considered that the uf series stand-alone is a mature technology product. At present, its application in some central departments is not good. The reasons are various, there are problems in selection, and the particularity of the vacuum cleaner itself. , Each factory has a problem with the uf series stand-alone, and the service of each factory has a problem. However, this cannot be said to be a product that cannot be used or matured. The death penalty cannot be arbitrarily imposed. At present, the air volume of cement and other industries is small, and the dust emission points are scattered, which requires reliable performance, simple structure, and small size of the dust removal equipment. This is why the uf series single bag dust collector can run at high speed from the beginning. The advantages of the series single dust collector are not Easy to be replaced by other equipment. Properly understanding, using and reforming it is positive.